February/March 2010 Pittcon Technology News

ANALYTICAL

PMB Moisture Analyzer
Booth 2605

PMB53 provides moisture determination results at 0.01%/1mg with a capacity of 50g
PMB202 provides results at 0.05%/10mg with a capacity of 200g
Tests can be run at virtually any location and results stored on the spot
A USB I/O port and bi-directional RS-232 interface are included for multi-connectivity

Adam Equipment
www.adamequipment.com

6100B Series Single Quadrupole LC/MS
Booth 2249

Features a quieter turbo pump
Small footprint: only 15 inches of linear bench space needed
Fully resolved peaks are not required for mass spectral analysis, allowing shortened chromatographic runs and reduced sample preparation
Includes various integrated validation features to help meet regulatory requirements

Agilent Technologies
www.chem.agilent.com

Trace 1300 Atomic Absorption Spectrometer
Booth 2025

Features quick auto-switch between Flame and GF atomizers
Fast wavelength scan takes 30 seconds to scan from 190-900 nm
Automatic acetylene flow rate control ensures hands-free operation
Features a built-in camera in the GF system for efficient method development

Aurora Instruments
www.aurora-instr.com

SpeedDigester K-439 Infrared Digestion System
Booth 1131

Pre-programmed with 20 commonly used methods and can store up to 50 methods
Heating chamber distributes heat to every sample, with no foaming
Features a tight exhaust manifold that connects to the B-414 scrubber to remove digestion vapors
Compatible with 300 ml sample tubes for standard Kjeldahl methods and 500 ml sample tubes

Buchi
www.buchi.com

Rotavapor® R-220 SE (Second Edition) Rotary Evaporator
Booth 1131

EasyClamp permits fast and safe installations while securing glass joints
New control panel provides bath, vapor and cooling temperatures without complex menu navigation
Features a new level sensor and USB module, which can record data and interface with peripheral equipment
An optional safety enclosure can be attached, which doesn’t restrict access to glassware

Buchi
www.buchi.com

Lead Selenide and Lead Sulfide Detectors with Integrated Electronics
Booth 2209

Expand measurement dynamic range, providing greater resolution for low signal detection
New technology reduces sensor footprint by up to 50% and lowers system costs
Provide temperature stabilization and lower power requirements
Ideal for many applications, including gas analysis, thermal imaging and flame detection

Cal Sensors
www.calsensors.com

WDXRF Portaspec® X Series X-Ray Analyzer
Booth 1820

Performs multi-elemental analysis in the range of Ti to U
Ideal for measuring coating weights of both chrome and titanium pretreatment
An adjustable goniometer allows a user to analyze up to five elements, one at a time
Features an easy-to-load, two-position sample holder

Cianflone Scientific
www.cianflone.com

1190 Particle Size Analyzer
Booth 2072

Incorporates three lasers for highest accuracy from 0.04 to 2,500 microns.
Switch between dispersion modes without having to switch hardware or realign the system
Optical components are permanently mounted on a cast iron base plate to ensure system is always aligned
Fully compliant with ISO 13320 and 21 CFR Part 11 standard

Cilas Particle Size
www.particle-size.com

Pressure Swing Adsorption ASAP 2050 Xtended Pressure Sorption Analyzer (xPSA)
Booth 1721

Features a pressure transducer capable of operating from vacuum to 10 atmospheres
May be used with a large variety of gases, including nitrogen, propane, butane and argon
Includes two independent vacuum systems, allowing simultaneous preparation of two samples
Sample prep and analysis can occur without interruption or cross-contamination

Micromeritics
www.micromeritics.com

Spectrometer for NIR Applications NIRQuest
Booth 3131

Available in versions for 900-1,700 nm, 900-2,050 nm and 900-2,500 nm coverage
Uses a high-performance Indium Gallium Arsenide (InGaAs)-array detector
Features grating and external triggering for high-resolution laser characterization
Capable of integration times as rapid as 1 ms

Ocean Optics
www.oceanoptics.com

Product Spotlight

GC-2010 PLUS CAPILLARY GAS CHROMATOGRAPH
FASTER ANALYSIS, REDUCED DOWNTIME AND SUPERIOR REPRODUCIBILITY

The new GC-2010 Plus Capillary gas chromatograph from Shimadzu Scientific Instruments meets the increased demands of trace-level analysis, ensuring data quality for a wide range of applications. With a redesigned collection of detectors that feature market-leading sensitivity and quick heating and cooling, the GC-2010 Plus improves separation performance, increases sample throughput and reduces operator time.

Third-generation Advanced Flow Controllers (AFC) support high-speed analysis at a maximum pressure of 970 kPa and 1,200 mL/minute maximum flow rate. Incorporating a double-jet cooling system and optimized air flow channels, the instrument enables a rapid cooling time of 450°C to 50°C in 3.4 minutes, allowing the next analysis to start sooner.

The unit’s detectors have been redesigned for greater compactness and higher sensitivity. The compact flame photometric detector (FPD) uses a condenser lens and total reflection system with mirrors for improved flame stability. Using clean detector gas flows and low-noise cables, the flame ionization detector (FID) achieves double the sensitivity of previous Shimadzu detectors, ensuring a minimum detected quantity of 1.5 pgC/s.

Reduced analysis time is achieved through the use of a backflushing system that reverses the flow of carrier gas. After all target compounds are detected, residual substances are backflushed from inside the column to the injection port.

For more information, visit www.ssi.shimadzu.com or visit booth 2069 at Pittcon 2010 in Orlando, Florida. Mark Taylor, GC product manager, can be reached at cmtaylor@shimadzu.com, or by phone at 800-477-1227 x.1896.

Masterflex L/S® Digital Pump Drives
Booth 2141

Feature high-accuracy motors and graphical interface for easier setup and operation
Brushless motor features a 6,000:1 turndown ratio for wider flow range
Enhanced dispensing features include volume dispense, timed dispense and copy/repeat
Programmable dispense interval allows hands-free dispensing and filling

Cole-Parmer
www.coleparmer.com

Series 542 Gas Distribution and Management System
Booth 3141

Built for use in the event of power loss or insufficient amount of gas
Automatically activates the reserve to provide gas supply without interruption
Check valves prevent back flow to the generator or reserve cylinder
Features a web server with proprietary software enabling remote programming and monitoring

CONCOA
www.concoa.com

Grace VisionHT™ HPLC Columns
Booth 3721

Provide ultra-fast separations for greater efficiency, sensitivity and resolution
Features a 12,000 psi rating, compatible with all ultra high-pressure LC systems
Optimized 1.5 μm media with ultra-low volume hardware
Features six high purity phases, each with unique separation benefits

Grace Davison Discovery Sciences
www.discoverysciences.com

XDS MasterLab™ Near-Infrared (NIR) System
Booth 2504

Integrated variable spot size for optimal sample illumination
Capable of non-destructive analysis of solids and liquids in less than a minute
Features network-ready analyzer for centralized database management
Change modules in minutes with no compromise in performance

FOSS NIR Systems
www.foss-nirsystems.com

Toy Analysis for Consumer Safety iCAP 6200 ICP Spectrometer
Booth 2757

Offers simple ‘out-of-box’ operation for rugged and consistent day-to-day sample analysis
Features compact design and simultaneous dual-view ICP emission spectrometer
Provides cost-effective analytical solution in labs with standard sample throughput requirements
Offers pre-optimized sample introduction settings and analysis-ready software method templates

Thermo Fisher Scientific
www.thermo.com

GC Leak Detector GLD PRO
Booth 2757

Designed for use with GC systems and their accessories, such as purge and trap systems
Detects smallest gas leaks (
Features thin, pencil-tip probe to pinpoint the leak site in hard-to-reach locations
Offers side grips for added durability and onehanded operation

Thermo Fisher Scientific
www.thermo.com

Product Spotlight

CORRELATIVE MICROSCOPY TOOL
COMBINES ATMOSPHERIC SCANNING ELECTRON MICROSCOPE WITH LIGHT MICROSCOPE

JEOL’s new ClairScope™ enables uncompromised observation of samples in their native state using a light microscope (LM) and an atmospheric scanning electron microscope (ASEM) to significantly reduce sample prep time and allow dynamic observation of real time processes.

The wide-field light microscope with emersion lens is co-axially aligned with the inverted electron column, making it easy to switch between LM and ASEM without moving the specimen dish. Samples can be observed dynamically at room temperature and at atmosphere, without having to wait for drying processes.

The specimen dish features an ultrathin SiN (silicon nitride) film window that separates the sample in atmosphere from the vacuum in the ASEM. An electron beam is projected from below to the sample on the film for high resolution imaging of the sample in atmosphere. The dish also makes it possible to add reagents, drugs and other substances to the sample in order to observe reactions in both liquid and gas environments.

Ideal for the life science and materials industries, dynamic processes such as platelet generation, microbe growth, crystallization, electrochemical reactions and dendrite growth can be followed in real time. No other products, add-ons or consumables are required, other than the sample holders.

For more information, visitwww.jeolusa.com or visit booth 2731 at Pittcon 2010 in Orlando, Florida. Donna Guarrera, assistant director SM Division at JEOL, can be reached atdguarrera@jeol.com, or by phone at 978-535-5900.

Sievers InnovOx On-Line TOC Analyzer
Booth 3645

Able to handle tough samples like brine and discharge water, with minimal maintenance
Uses a Supercritical Water Oxidation (SCWO) technique to achieve superior TOC recoveries
Features a wide dynamic operating range of 0.5 to 50,000 parts per million TOC
Includes extended calibration stability and user-configurable alarms and outputs

GE Analytical Instruments
www.geinstruments.com

C11118GA Process NIR Spectrometer
Booth 2326

Capable of measuring all wavelengths simultaneously, preventing data blur from rapidly changing samples
Proprietary master transmission grating provides higher performance from 2,000 to 2,550 nm
Programmable integration times range from 6 to 40,000 μs covering 900 to 2,550 nm
Features seven selectable triggering modes and two gain modes

Hamamatsu
www.sales.hamamatsu.com

CMS5000 Monitoring System
Booth 620

For continuous, unattended remote monitoring of water or air
Analyzes and quantifies Volatile Organic Compounds (VOCs) and Toxic Industrial Chemicals (TICs) for accurate results within minutes
Requires virtually no operator involvement after initial installation and setup
CMS IQ software enables management of sample collection and analysis sequence

INFICON
www.inficon.com

I-Graph X Portable Gas Chromatograph
Booth 3505

No external carrier gas supply required
Integrated vacuum pump allows for measurement of non-pressurized samples
Features active column cooling, allowing for a lower starting temperature
Analysis time ranges from 30 seconds to 3 minutes

Inrag
www.inrag.ch

3Q Molecular Analzyer™ Series A Triple Quadrupole Mass Spectrometer
Booth 1857

Features a UniField™ ion detector capable of instant polarity switching
Includes multi-orthoganal HSID™ technology combined with enhanced flow for smooth transfer of ions with minimal loss
Torrent™ coaxial flow ion source provides high sensitivity for a wide flow rate range
Vertical orientation decreases required bench space

IONICS Mass Spectrometry Group
www.ionics.ca

NRS-5000/7000 Series Raman Spectrometers
Booth 3457

Capable of integrating as many as 8 excitation lasers from the UV to the NIR
Offer high-speed imaging using the Software Programmable Raman Integration System (SPRIntS)
Verti-Scan ensures consistent confocal sample excitation for undistorted 3D images
Dual Spatial Filtering reduces sample fluorescence while enhancing spatial resolution

JASCO
www.jascoinc.com

AQUA COUNTER® Karl Fischer Coulometric Titrator
Booth 2810

Allows two titration stations to run parallel with various volumetric/coulometric combinations
Reduces the use of expensive KF reagents
Features an ultra-trace moisture measurement mode accurate to ≤10μgH20
Equipped with a built-in thermal printer with high resolution printouts

JM Science
www.jmscience.com

iVisc Capillary Viscometer
Booth 3108

Capable of calculating polymer data, such as SV-, IV-, and K-values
Measurement of kinematic viscosity in accordance with DIN 51562 and ASTM D445
Employs energy-efficient technology; only 1 watt power consumption
A proprietary thermostat can be used to stabilize temperature

LAUDA-Brinkmann
www.lauda-brinkmann.com

TD-100™ Thermal Desorption Instrument for VOC and SVOC Analysis
Booths 1806 and 1808

Incorporates sample re-collection for repeat analysis and electrical cooling to lower running costs
Couples to any make of GC or GC/MS and complies with standard methods
Capable of the sequential analysis of up to 100 sorbent tubes
Includes RFID sample sorbent tube tracking technology (TubeTAG™)

Markes International
www.markes.com

MMS-4000 Thermogravimetric Analyzer
Booth 2156

Features auto loader with capacity for 77 samples
Furnace carousel, balance pedestal and crucibles are made of a special metal alloy for high temperatures
Device can operate without user attention
Temperature range of 50°C to 1000°C, ± 1°C

Navas Instruments
www.navas-instruments.com

MC500 Multi-Parameter Colorimeter
Booth 2008

Features a 6 LED photodetector array which supports 70 pre-programmed methods and 20 user-defined methods
Uses proprietary “Open Reagent System,” which uses Powder Packs, tablets and liquid reagents
Internal memory can store up to 1,000 data sets
Comes with 24 mm sample cells, 10 mm sample cells and 16 mm tube adapter

Orbeco-Hellige
www.orbeco.com

KrudKatcher™ Ultra Column Protection Device
Booth 3659

Rated up to 20,000 psi (1,375 bar), making it compatible with the highest pressure UHPLC columns
Removes microparticulates from LC flow stream, without contributing to system backpressure
Can be used with columns from 1.0 to 4.6 mm in diameter
Includes an integrated 0.5 μm 316 stainless steel filter element

Phenomenex
www.phenomenex.com

HPR Series Reactors for High Pressure Chemistry
Booth 2523

Range in size from 50 ml to 4 L and may be operated up to 10,000 psi and 350°C
Feature a magnetically coupled impeller for optimal mixing
Compact enough to fit easily inside a fume hood
All high pressure components are ASME rated and protected by a rupture disc for safe operation

Supercritical Fluid Technologies
www.supercriticalfluids.com

GC-2010 Plus Capillary Gas Chromatograph
Booth 2069

Employs Advanced Flow Technology, a redesigned suite of detectors with heightened sensitivity and fast heating and cooling
Features a backflush system to prevent column deterioration and detector contamination
Redesigned oven enables rapid heating and cooling: cools from 450°C to 50°C in 3.4 minutes
Gas-saver function saves carrier gas exhausting from the split line by incorporating a decreasing split ratio

Shimadzu Scientific Instruments
www.ssi.shimadzu.com

RF-20A and RF-20Axs Fluorescence Detectors
Booth 2069

Use a newly designed optical system to achieve high sensitivity levels
RF-20A has a water Raman S/N ratio of at least 1,200 and 2,000 for RF-20Axs
Provide 10 ms response, permitting ultra-fast LC without loss of separation
Allow highly sensitive, multi-component analysis using wavelength switching via a time program

Shimadzu Scientific Instruments
www.ssi.shimadzu.com

GFM Pro Flowmeter
Booth 2757

Capable of measuring both positive and negative vacuum flows from 0.5 to 500 ml/min and -0.5 to -500 ml/min
Measures the volumetric flow of any gas with an accuracy of ± 2%
Unit deploys an automatic shut-off when the measured flow exceeds 600 ml/min
Ideal for use with any gas, even those that are flammable or explosive

Thermo Fisher Scientific
www.thermo.com

GUARDION®-7 GC-TMS
Booth 735

Now available with rechargeable batteries that last up to 6 hours
New high-speed capillary GC is combined with a mini torodial ion trap mass spectrometer (TMS)
Features an on-board helium carrier gas cartridge
Electronic pressure control (EPC) of helium carrier gas provides rapid separation of analytes in less than 3 minutes

Torion
www.torion.com

Mobile Perfluoronated Tracer (PFT) Analyzer
Booth 2252

For the analysis of feeder oil leaks in high voltage feeder lines
Uses dual ambient sorbent trabs to trap and desorb an ambient air sample to a GC every 90 seconds
Sampling is fully automated by Wasson-ECE’s control software
When the system detects a PFT leak, an alarm is sounded and the leak is marked on a GPS map

Wasson-ECE
www.wasson-ece.com

SYNAPT™ G2 Quadrupole Time-of-Flight Mass Spectrometer
Booth 3155

Features a data acquisition rate of 20 spectra per second
Employs QuanTof Technology, to ensure exact mass data in UPLC® timeframes
Delivers simple and rapid data interpretation using MassLynx™ Informatics
Includes IntelliStart™ Technology for simplified system setup and automatic control

Waters
www.waters.com

ACQUITY® UPLC BEH200 SEC Columns
Booth 3155

1.7 μm columns for size-exclusion chromatography
For identification and quantification of glycan profiles from biopharmaceutical proteins
Applies UPLC technology for quantitative analysis of proteins, such as therapeutic mAbs
Features eCord™ Technology for recording critical individual column use parameters

Waters
www.waters.com

BASIC LAB

Independence™ Ductless Fume Hood
Booth 2741

Silconazyne™ allows for one gas phase filter that fits most gas phase applications
On-board chemical database features more than 1,000 approved chemicals
Includes a built-in gas analyzer that produces absolute exhaust and Interfilter™ values
Includes AirClean® Operating System, written entirely by AirClean® Systems

AirClean Systems
www.aircleansystems.com

Purair Advanced Ductless Fume Hoods
Booth 3913

Face velocity at 100 fpm ensures containment of fumes
An alarm will alert the operator when the airflow falls to an unacceptable level
The work area features a removable spillage tray which can be easily cleaned
Main filter can be chosen from 14 different types of carbon

Air Science
www.air-science.com

Powder Flow Tester
Booth 3111

Minimizes the downtime and expense that occur when hoppers/silos fail to discharge
Features various test options, such as Flow Function, Wall Friction and Bulk Density
Choice of Flow Function tests: Demo, Standard or High Precision
Compact, vertical design with small footprint fits easily on workbench

Brookfield Engineering
www.brookfieldengineering.com

Nano Spray Dryer B-90
Booth 1131

Heater technology is based on porous metal foam for laminar gas flow in drying chamber
Optimal energy input guarantees fast heating times up to 120°C
Dried particles are separated by an electrostatic particle collector
Produces submicron or nanoparticles from 300 nm to 5 μm with narrow distribution

Buchi Corporation
www.mybuchi.com

Product Spotlight

CYLINDER-BASED MICROARRAY TECHNOLOGY
DISCOVER INTRICATE OFF-RATE MEASUREMENT WITH HYBCELL TECHNOLOGY

Hybcell is the first DNA or protein microarray based on the use of cylinders instead of slides. These cylindrical microarrays yield robust hybridization and reproducible results by rotational sample agitation.

The hybcells are robotically processed by the hyborg—a fully automated, compact device that can hold up to 96 hybcells at a time. Hyborg integrates thermocycler, hybridization station and scanner all in one unit. Temperatures, buffers and multiple scans are freely configurable, providing the greatest flexibility and kinetic analysis.

In typical microbiology, where it can take 48 hours for a sample to produce results, hybcell technology provides results within ten minutes for a multiplexed ELISA, up to two hours for a compact sequencing application, all while delivering hundreds of results for a single sample (presence of bacteria, viruses, genes, antibodies, etc).

Hybcell technology offers selectivity (elimination of unspecific binding effects), measurement of binding kinetics, assay versatility, fully automated assay operation and minimum user intervention.

Hybcells can be filled by either a pipette or automated robot. Each sample is then linked to a unique bar code. Once the hybcells are transferred to the hyborg, all further processes are automated, reducing the risk of user errors.

For more information, visit www.anagnostics.com. CEO Christoph Reschreiter can be reached at c.reschreiter@anagnostics.com, or by phone at +43 7252 58193-0.

Nitrogen Generators NitroVap-1LV and NitroVap-2LV
Booth 1557

Produce more than 320 LPM of pure evaporationgrade nitrogen
Require less than 1 square foot of bench space and can supply more than 100 evaporator nozzle positions
Use a combination of filtration and membrane separation technologies
High-efficiency coalescing filters remove all contaminants down to 0.01 micron

Parker Balston
www.labgasgenerators.com

Continuous Roll Microplate Heat Sealer TriSeal Pro

Includes a 610 meter film roll, enabling up to 5,000 plates to be sealed without intervention
Features a turntable design, which allows simultaneous loading, unloading and sealing
Capable of sealing three plates per minute
Features adjustable temperature control from 50°C to 185°C

Porvair Sciences
www.porvair-sciences.com

Traceable® Conductivity/ TDS/Salinity Meter
Booth 3331

Elimination of operator technique lets everyone in the lab report identical readings
Features instant-response probe and solid-state thermistor for precise readings
Dual display shows reading and temperature
Features a tough, chemical-resistant, waterproof ABS housing

Control Company
www.control3.com

ANALYSETTE 22 Micro Tec Plus Laser Particle Sizer
Booth 1829

Features extra-wide measuring range of 0.08 – 2,000 μm
Employs dual-laser technology
Wet dispersion unit includes a centrifugal pump for transporting even heavy particles
Measuring cells come in convenient cartridges

Fritsch
www.fritsch.de/en

PULVERISETTE 6 Planetary Ball Mill Premium Line
Booth 1829

Features automatic imbalance compensation and a grinding bowl lock system
Able to grind larger sample quantities down into the nano range
Includes a special emptying device with 2 sieves for grinding bowls
EASY GTM ensures the set grinding parameters are not exceeded

Fritsch
www.fritsch.de/en

Specialty Gas Control Panel P3500 Series
Booth 2846

Provides continuous gas supply without interrupting the system during cylinder replacement
When primary bank is nearly empty, the reserve bank will automatically supply gas to the system
Each regulator is mounted on individual panels for in-line repair
Available in either stainless steel or brass; single- or dual-stage configurations

Genstar Technologies
www.genstartech.com

U-Series Nebulizers for ICP
Booth 3171

Sample channel is uniform from entry point to tip to prevent blockages
VitriCone construction, with heavy glass capillary, resists vibration
UniFit sample connector provides a simple connection with no dead volume
Compatible with all ICP-OES and ICP-MS models

Glass Expansion
www.geicp.com

ZEUS Pipetting Module for IVD Instruments
Booth 1669

Aspirates volumes from 1 μL to 1,000 μL
Ideal for any IVD instrument requiring on-board pipetting
Qualitative Pipette Monitoring (QPM) automatically detects, reports and handles pipetting errors according to user-defined procedures

Hamilton Company
www.hamiltoncompany.com

Micron Air Jet Sieve
Booth 1641

Employs the pneumatic sieving principle for enhanced accuracy and reproducibility of particle size analysis
Able to quickly and accurately identify particles ranging from 20 to 4,750 microns
Rotating wand eliminates the need for tapping
Features a vacuum system for strong, quiet performance

Hosokawa Micron Powder Systems
www.hmicronpowder.com

Presto® PLUS Series Temperature Control System
Booth 2747

Combines rapid heat-up and cool-down times with wide working temperature ranges
Bath fluids can be used with an extended temperature range and a long lifetime
Features increased heating capacity, adjustable fluid flow and stability to ±0.01°C
Includes splash-proof keypad

Julabo USA
www.julabo.com

FlexStream™ Modular Gas Standards Generator
Booth 1650

Offers total flexibility for creating precision gas mixtures
Features up to six independently controlled channels
Can be controlled remotely by a PC or process computer using Modbus® connectivity
Features an internal microprocessor to set the operating mode and adjust dilution flow

KIN-TEK Laboratories
www.kin-tek.com

Purifier® Cell Logic® Biosafety Cabinets
Booth 1020

Scope-Ready™ feature allows a customer-supplied microscope to be integrated into the cabinet
Pure-Vu™ Seal allows a clear view into the cabinet
Features a Stand-Still Isolation Platform which reduces vibration up to 300%
Temp-Zone™ option keeps heated or chilled samples at their ideal temperatures

Labconco
www.labconco.com

Product Spotlight

LIQUID DOSING MADE SIMPLE
TRANSFER CORROSIVE LIQUIDS WITHOUT HAVING TO MEASURE AND POUR

KNF Neuberger designed its new SIMDOS® diaphragm liquid dosing pump with simplicity and ease in mind. Ideally suited for transferring corrosive liquids in the lab, the pump is available with a variety of wetted materials, including PTFE/FFPM.

The SIMDOS pump achieves fast, precise calibration within a short amount of time, transferring liquids at a flow rate of 0 to 100 ml per minute. Offering consistent reliability throughout entire processes, SIMDOS makes programming and access of all functions simple and intuitive.

Safety is a definite concern, with the pump head located outside the splash-protected IP-65 housing. The pump is safe to run dry and is self-priming in up to 9 feet of water. It can handle pressures of up to 90 psig and can transfer viscous media up to 150 centistokes.

Roland Anderson, laboratory product manager at KNF Neuberger, says SIMDOS has many benefits over conventional pumps. “Most people use a peristaltic pump,” he said. “When you factor in the bending and aging of the tubing, performance starts to vary over time. The [SIMDOS] doesn’t use any tubing, and it gives consistent results throughout its life.”

The pump’s electronic display, combined with a touch control knob, makes accessing all of its functions very simple. “It’s designed so it’s plug and play,” Anderson added. “You can plug it in… walk away, and have it dose in the way you programmed it.”

For more information, visit www.knf.com/labnew.htm or visit booth 1935 at Pittcon 2010 in Orlando, Florida. Roland Anderson, Laboratory Product Manager, can be reached at randerson@knf.com or by phone at 609-890- 8600 ext. 241.

852 Titrando
Booth 1121

Automatically recognizes sample additions
Features fully automatic reagent exchange
Bromine index can be determined
Dosino® dosing technology eliminates build-up of air bubbles

Metrohm USA
www.metrohmusa.com

G7893 Glassware Washer
Booth 869

A complete washing and drying cycle takes one hour
Saves space with a 24-inch footprint
Incorporates true HEPA-filtered forced-air drying
A cool-down step can be programmed at the end of cycle to ensure glassware is safe to handle

Miele
www.labwasher.com

PG8527 Glassware Washer
Booth 869

Cleans hundreds of pieces of glassware, using minimal water, detergent and electricity
Features gentle start pumps so small items can be safely cleaned
Features split-level cleaning so tall and short items can be cleaned in one wash load
Includes a maintenance-free conductivity monitor and a self-draining wash chamber

Miele
www.labwasher.com

Q-POD® Element Unit
Booth 1769

Ensures delivery of ultrapure water with very low levels of elemental contamination
Features a footswitch for hands-free water delivery
Ideal for use in a Class 1000 clean room environment
Supplies water in volumes required by the user (up to 1.5 L/min)

Millipore
www.millipore.com

Centrifan™ Recirculating Evaporator
Booth 3109

Dramatically accelerates the evaporation of aqueous and organic solvents
Operates without a vacuum pump, to prevent sample bumping or cross contamination
Eliminates oil cleanups, heat, noise and tubing typically associated with a vacuum pump
Available with various rotor configurations

Modular SFC
www.modularsfc.com

Wood Casework
Booth 3334

Each cabinet is made to order
Cabinets are solid and offered in a unique full top frame
Drawers are fully dovetailed in all corners and finished with the same flat line finish as the rest of the cabinets
LEED projects are welcomed and encouraged

Mott Manufacturing
www.mott.ca

Balston H2PEM Series Hydrogen Generators
Booths 1451 and 1557

Produce over 510 cc/minute of 99.9995% pure hydrogen
Features a unique water hydration circulation system
Allow GC users to supply, control and automate all hydrogen gas supplies
A single generator can support as many as 20 instruments with fuel gas

Parker Hannafin
www.parker.com

LCMS-SF5000NA Super Flow TriGas Generator
Booths 1451 and 1557

Produces gas which exceeds the requirements of any LC/MS requiring 3 independent gases
Includes self regenerating compressed air dehydration membranes
Provides enough gas for a single LC/MS instrument on a continual basis
Eliminates the need for expensive, high pressure nitrogen and zero air cylinders

Parker Hannafin
www.parker.com

ABN2ZA Nitrogen Generator
Booth 3469

Combines two separate gas generator systems in one unit
Removes oxygen, moisture and other gases to leave clean, dry, phthalate-free nitrogen and air
Fitted casters allow the user to easily position the unit in the lab
No external compressor required

Peak Scientific
www.peakscientific.com

LaboStar™ Water Purification System
Booth 1111

Produces analytical grade water on demand
Features easy push-button operation and quick sanitization regimens
Recirculation feature maintains optimal water quality while minimizing bacterial growth
Produces up to 18 megohm ASTM water quality

Siemens Water Technologies
www.siemens.com/pittcon

Compod™ Programmable Control Module
Booth 1634

Permits networking of multiple instruments using open-source MODBUS RTU protocol
Monitors the functionality of mass flow meters or controllers
Controls simple processes without the need for external PLCs or computers
Monitors the operation of instruments and provides potential problem alerts

Sierra Instruments
www.sierrainstruments.com

STRIKE300 Rotary Evaporator
Booth 3502

Transparent shield protects the user and working environment from moving parts
Can be connected to a vacuum controller and/or temperature controller
Includes an LCD interface and touch screen
Mechanical sealing system guarantees a constant vacuum-tight seal

Steroglass
www.steroglass.it

ColonyDoc-It Imaging Station

Lets users quickly and accurately count colonies with quick click software interface
Features multiple excitation sources to visualize white light and fluorescent colonies
High-resolution digital color camera identifies even the smallest colonies
Accommodates plate and filter sizes from 33 mm to 150 mm

UVP
www.uvp.com

Life Science

ChiralRAMAN-2X™ ROA Spectrometer
Booth 1841

Combines Raman microscopy, Raman spectroscopy and Raman optical activity in one instrument
Applications include structural characterisation of chiral molecules and biologicals such as proteins, sugars and viruses, as well as SERS and SEROA experiments

BioTools
www.btools.com

Product Spotlight

Laser Particle Size Analyzer
Tri-Laser Design Ensures Accuracy Across Entire Measurement Range

The 1190 Particle Size Analyzer from Cilas Particle Size integrates three lasers to provide accuracy and precision from 0.04 to 2,500 microns. Measurements can be made in either liquid or dry dispersion modes and switching modes can be done with a single click of the mouse. The fully programmable dispersion system eliminates the need for the user to change hardware and it can switch between modes without having to be realigned. All optical components are mounted on a rigid cast iron base plate to ensure that the system is always aligned.

The integration of a CCD camera offers users the ability to measure an extended range of samples while maintaining a short bench design, providing for a more rugged tool. This concept allows the measurement range to be extended without increasing the size of the instrument.

Cilas’ ExpertShape Image Analysis software allows for the measurement of shape parameters such as aspect ratio, perimeter, area, shape factor and fiber length. The 1190 also includes a free fall module for users who want to analyze their samples in their naturally agglomerated state.

For more information, visit www.particle-size.com. Product Manager Richard Nameth can be reached at richard@particle-size.com or by phone at 608- 274-7719. Cilas Particle Size will be at Pittcon 2010 in Orlando, Florida at booth 2072.

Cell Imager
Booth 1669

Accurately measures cell confluence and growth in 96-well plates
Reads an entire 96-well plate in about 5 minutes
Two positions allow one plate to be imaged while another is processed
Software provides live data tracking for an overview of cell confluence in all plate wells

Hamilton Robotics
www.hamiltonrobotics.com

F-2700 Fluorescence Spectrophotometer
Booth 2041

Available in two configurations: stand-alone or PC-controlled
Features a signal-to-noise ratio of 800 S/N RMS (Raman band of water at 5 nm bandwidth)
With PC control the scan speed can reach 12,000 nm/min
Available accessories include automatic sampling and quantum yield measurement

Hitachi High Technologies America
www.hitachi-hta.com

2-D Omni Spray® Ion Source
Booth 1335

Based on Desorption Electrospray Ionization (DESI)
Features an automated surface platform to enable rapid sampling and surface imaging
Can handle samples up to 76 mm by 114 mm (about the size of a 96-well plate)
Capable of analyzing 96 sample spots in less than 10 minutes

Prosolia
www.prosolia.com

SR7000DC Surface Plasmon Resonance (SPR) System
Booth 1760

Provides real-time measurements of biomolecular interactions
Micro or macro flow cells are available for different surface work
Fluidic configurations range from manual to fully automated with an optional autosampler

Reichert
www.reichertspr.com

LIM & Software

HPLC Troubleshooting e-Learning Modules
Booth 4003

How to identify problems and recognize the underlying causes
Covers blockages, leaks, baseline/peak distortions, component malfunctions, etc.
Customization capability enables you to add your own tips to the program
Licenses range from short-term to permanent and single computer or network

Academy Savant
www.academysavant.com

MolAna™ Acquisition and Quantitation Software
Booth 1857

Provides full data acquisition capability, including multiple overlapping experiments within the same method
Enables a user to extract and perform quantitation for data collected in any analysis mode
Includes a user-friendly, workflow-oriented interface and simple method setup
Features fast curve fitting and integration and import/export capabilities

IONICS
www.ionics.ca

Nexxis iLAB Laboratory Automation Software
Booth 3969

Automatically delivers information from application to application in real time
Updates informatics systems as events take place
Provides real-time management of lab workflow
Controls procedural execution and ensures that SOP requirements are always met

Labtronics
www.labtronics.com

Nexxis ELN Electronic Laboratory Notebook
Booth 3969

Provides real-time workflow control and automation for R&D and QA/QC testing
Includes a fully searchable system that provides instant access to worksheets and notes
ReDI™ technology ensures rapid deployment, transforming existing paper documents into electronic forms that are ready to use in minutes

Labtronics
www.labtronics.com

LimsLink Integration Software
Booth 3969

Integrates any instrument to any LIMS, eliminating data entry errors and reducing data review and approval times
Includes a fully searchable system for storing raw data
Features automatic creation of worklists and sequence files and automatic calculations
Interfaces are fully configurable without custom coding

Labtronics
www.labtronics.com

UN-SCAN-IT Graph Digitizing Software
Booth 2903

Automatically converts scanned graphs to useful (x, y) data using a simple drag and drop interface
Works with any scanner or image input device
Can digitize journal graphs, strip chart output, old graphs and other hard-copy graphs
Able to integrate peak areas, smooth data, take derivatives, re-scale graphs and store data

Silk Scientific
www.silkscientific.com

SmartLab CIMSplus Freedom Workstation
Booth 3973

Provides comprehensive tracking and tracing of all consumables
Manages all workflows for lab consumables, reagents, solutions, columns, etc.
Integrates with pH meters and balances
Includes a bar code reader and printer for compliant control

VelQuest
www.velquest.com

OEM Driver Software SeaBreeze
Booth 3131

Basic starting platform can be customized by developers for their own applications and instruments
Delivers faster processing and is compact enough to be built directly into spectral libraries smaller than 500k
Can be adapted to new platforms by providing a native implementation of bus interfaces for the target
Supports most Ocean Optics’ USB spectrometers for Linux and Windows operating systems

Ocean Optics
www.oceanoptics.com

Professional SaaS-based LIMS SciLIMS SSM: Professional Edition

Eliminates restrictions in many areas (users, container types, storage units, etc)
Customizable to the lab’s requirements, without costly administration services
Eliminates the need to purchase servers and maintain software
Includes a 30-day money-back guarantee

Sciformatix
www.sciformatix.com

Supplies & Consumables

High-Performance Labels for Histology and Pathology
Booth 2110

Include Flexible Lamination After Printing (FLAP) labels to withstand harsh chemicals and stains
Labels designed to stay adhered to histology cassettes
Designed to withstand the cryogenic process
Available as print-on-demand in conjunction with CAB printers and label design software

Computype
www.computype.com

Cryo Hold Liquid Nitrogen Blank Label
Booth 2110

Fully customizable; designed and tested for cryogenic applications
Extends Computype’s Cryo Hold series for use with Liquid Nitrogen
Resistant to harsh chemicals and extreme temperatures
Customized to match any laboratory scenario

Computype
www.computype.com

InGuard™ Sample Prep Cartridges for Ion Chromatography
Booth 969

Packed with resins to automatically remove matrix interferences (anions, cations, lipids, etc.)
Plumbed directly after the injection loop and before the concentrator column, saving time
Available in silver (Ag), hydronium (H), sodium (Na), hydrophilic reversed phase (HRP) and combined Na/HRP
Each cartridge can be used several times before needing replacement

Dionex
www.dionex.com

OxiClear™ Gas Purifiers
Booth 2837

Feature low resistance to gas flow
Remove oxygen and trace amounts of water and organics from inert carrier gases
Efficient to less than 5 ppb when the incoming oxygen concentration is 15 ppm or less
Able to withstand temperatures up to 100°C

LabClear
www.labclear.com

OC Line of Lubricants and Thread Sealants
Booth 3208

Oxygen compatible and chemical-resistant
Thermally stable over a wide temperature range
Non-flammable, non-migrating, non-toxic, odorless, waterproof and chemically inert
Suitable for high-pressure applications

MPT Industries
www.mptindustries.com

Smart pH Cuvettes
Booth 3131

Coated with sol gel embedded with Bromocresol Green pH indicator dye
Available in plastic (PMMA) or quartz, and measure 1 cm x 1 cm
Proprietary pH-sensitive materials can be formulated as self-adhesive patches and integrated into various sample containers
Compatible with various sampling devices and fiber optic spectrometers and accessories

Ocean Optics
www.oceanoptics.com

Plastic Protective Packaging
Booth 4047

Over 3,000 types and sizes of packaging for consumer and promotional items
Markets include hobby/craft, cutting tool & engineered parts industries and DIY markets
Provide custom design, development and production for specific requirements

Rose Plastics
www.rose-plastic.us

National Scientific Mass Spec Certified Vials
Booth 2757

Manufactured from inert, pure and chemically stable glass
Produced under strict quality control protocols for uniformity
Feature ultra-high purity bonded PTFE/silicone closures
Each vial undergoes verification of 13 critical physical characteristics

National Scientific
www.nationalscientific.com

A+ Single Element Calibration Standards
Booth 3341

Designed for use in ICP-MS, ICP-AES, AA and other spectrometric techniques
Assayed in accordance with the High Performance ICP (HP-ICP-AES) method developed by NIST
HP-ICP-AES method ensures highest accuracy standards available
Provides traceability to NIST

VHG Labs
www.vhglabs.com

Microplate 2 mL Compound Storage Plate

Provides high integrity sample sealing and near zero well-to-well cross contamination
Manufactured from ultra-pure grade polypropylene under clean room conditions
Contains no contaminants that can leach into stored samples
Complies with ANSI/SBS dimensions, ensuring compatibility with all microplate readers, washers and automated equipment

Porvair Sciences
www.porvair-sciences.com

Universal Valve Actuator
Booth 2315

Covered by three actuator versions: high speed, medium speed/torque and high torque
Includes a universal 24 volt DC power supply and manual interface
CE/RoHS compliant
Includes a variety of interface options including RS232/485, USB and BCD

Valco Instruments
www.vici.com

HPLC Vials Prominence
Booth 2069

The 1.5 mL and 4 mL sample vials use a PTFE/silicone septum
Uniformity of vial bottom thickness ensures consistent needle depth from run to run and minimizes user intervention
6 mm opening provides a better target for autosampler needle, for easier filling
Available in 1 mL, 1.5 mL, 4 mL, 13 mL, 200 μL and 300 μL sizes

Shimadzu
www.ssi.shimadzu.com

Product Spotlight

CONFIGURABLE MICROSCOPE SYSTEM
CUSTOMIZED OPERATION FOR UP TO TEN USERS

The new Axio Imager 2 microscope from Carl Zeiss promotes maximum flexibility and ease of use. The customizable options of the ten stand versions make it easy to achieve optimal performance and functionality. The light manager can store and reproduce the illumination intensities for each magnification, while the motorized stands allow one to select stored contrasting techniques via the contrast manager.

The microscope’s multi-user capabilities can store vital system parameters for up to ten users, making it simple for everyone in the lab to have their settings readily available to them. The Z-stand features a high-performance focus drive, with which a user can perform even the smallest focus movements.

The Axio Imager 2 features a new optical design for the transmitted light beam path and the condensers, permitting homogenous illumination at low magnifications and an even greater working distance. Two added functions are the ability to automatically switch between reflected and transmitted light and the generation of mixed light, for areas of research involving living cells or organic tissue.

The AxioVision software automatically stores important magnification, contrast and illumination data. The triggerable LED light source for Köhler illumination, integrated with the z-piezo insert, offers rapid acquisition of Z-stacks or high resolution overview images.

For more information, visit www.zeiss.com/micro or visit booths 4051 and 3951 at Pittcon 2010 in Orlando, Florida. Kristen Orlowski, Product Marketing Manager, Light Microscopy, can be reached at korlowski@zeiss.com, or by phone at 860-316-7648.