Nitrogen vs. Centrifugal Evaporators for High-Throughput Sample Concentration

Ninety-six samples will tie up a rotovap for days. Nitrogen blowdown and centrifugal evaporators both handle them in a run, but they win on different solvents and cost money in different ways: gas versus vacuum.

Written byTrevor J Henderson
| 5 min read
Lab supervisor loading tubes into a nitrogen blowdown evaporator in a fume hood, with a nitrogen generator and centrifugal evaporator nearby.
Register for free to listen to this article
Listen with Speechify
0:00
5:00

Key takeaways

  • A nitrogen evaporator directs a stream of gas onto each heated sample at atmospheric pressure, while a centrifugal evaporator spins samples under vacuum with heat, so they boil from the top down without bumping.
  • Nitrogen blowdown is often faster for volatile organic solvents such as methanol, acetonitrile, and dichloromethane; centrifugal systems win for water, DMSO, and DMF.
  • Nitrogen blowdown’s main running cost is gas: one manufacturer uses 0.33 L/min per position, while other systems use several times more, so consumption varies widely by model.
  • On-site nitrogen generators can cost less than cylinders over time for regular users, while centrifugal evaporators avoid gas entirely but need vacuum pumps and higher upfront investment.
  • Choose by solvent, sample format, throughput, and whether samples must stay independent or can share one chamber.

 

Hand a rotary evaporator 96 samples and it will be busy for days, one flask at a time, with someone watching each endpoint. That’s why high-throughput labs concentrate samples in parallel. The Indiana State Department of Toxicology, for example, processes nearly 1,000 blood and drug samples a month for criminal cases using a 100-position nitrogen evaporator, according to the manufacturer’s account.

What is the difference between a nitrogen evaporator and a centrifugal evaporator? A nitrogen blowdown evaporator sweeps solvent vapor away from each heated sample with a gas stream at atmospheric pressure; a centrifugal evaporator spins samples under vacuum with heat, lowering boiling points and using centrifugal force to prevent bumping. Nitrogen blowdown usually wins for volatile organic solvents, and centrifugal systems win for water, DMSO, and DMF. Their costs differ too: one burns gas, the other runs a vacuum pump. This article compares them with practical scenarios. For rotary evaporators and the wider picture, see our guide to lab evaporators.

What is the difference between a nitrogen evaporator and a centrifugal evaporator?

Nitrogen blowdown evaporators

  • How it works: samples sit in a heated block or water bath while needles direct nitrogen just above each surface, continuously replacing vapor-saturated air.
  • Strengths: fast with volatile organics, simple to run with no vacuum system, and each sample has its own gas stream, which one manufacturer notes can help minimize cross-contamination.
  • Limits: slow for water and high-boiling solvents, ongoing gas cost, and solvent vapor that must go into a fume hood or exhaust.

Centrifugal evaporators and vacuum concentrators

  • How it works: a rotor spins tubes, vials, or plates inside a heated vacuum chamber; centrifugal force creates a pressure gradient so samples boil from the top down, as a general reference explains.
  • Strengths: no gas supply, handles water, DMSO, and DMF, prevents bumping, and suits microplates; high-performance systems remove DMSO while keeping samples below 40 °C, the same reference notes.
  • Limits: all samples share one chamber, vacuum level, and temperature; vacuum pumps need maintenance; and some lids and components aren’t compatible with aggressive solvents, which is why distributors such as VWR list glass-lid models for acetone, acetonitrile, ethanol, and DMSO.

Which is faster? It depends on the solvent

For volatile solvents, gas flow is efficient. In a manufacturer’s head-to-head test, a nitrogen blowdown unit evaporated 1.5 mL of methanol from 2 mL tubes in 30 minutes at 35 °C, while a centrifugal concentrator needed 40 minutes. The same company acknowledges centrifugal systems keep the advantage for DMSO, DMF, and heavily aqueous samples, because vacuum lowers their boiling points, and its selection guide makes the same point. It even offers an interactive tool based on measured evaporation rates. Since these comparisons come from a nitrogen evaporator maker, treat exact times as indicative and test your own samples.

  • Methanol, acetonitrile, hexane, ethyl acetate, dichloromethane: nitrogen blowdown is usually faster.
  • Water and aqueous buffers: centrifugal or vacuum concentration is usually faster and gentler.
  • DMSO, DMF, NMP: centrifugal evaporation is the practical choice.
  • Mixed solvents: test both, or remove the volatile fraction first.

What does nitrogen really cost?

Gas consumption is the hidden variable. One manufacturer’s total cost of ownership analysis assumes 0.33 L/min per position, 40 minutes a day, and 250 workdays a year, with 300 cubic foot cylinders holding about 8,495 L. A generator vendor gives a much wider range of 0.5 to 2 L/min per position for parallel evaporators. Run the numbers for a 24-position unit on that schedule and annual use falls anywhere from roughly 79,000 L to 480,000 L, or about 9 to 56 cylinders a year. Model choice alone can swing consumption several-fold; the same manufacturer’s comparison reports large differences in rated gas input between 24-position models from different makers.

  • Turn off empty positions. One manufacturer recommends individual flow control, since basic units blow gas into every position whether or not a sample is present.
  • Set needle height and flow carefully: a gentle dimple on the surface evaporates efficiently without splashing.
  • Consider a generator. The TCO analysis reports on-site generation up to 65% cheaper than cylinders over 10 years for its scenarios; results depend on how much gas you use.
  • Watch the room. High-flow nitrogen in small, poorly ventilated rooms can displace oxygen; run evaporators in fume hoods and follow your institution’s guidance on oxygen monitoring.

Centrifugal evaporators avoid gas costs entirely, but typically cost more to buy and need vacuum pump maintenance, cold traps for solvent capture, and electricity for refrigeration where fitted.

Lab manager academy logo

Lab Quality Management Certificate

The Lab Quality Management certificate is more than training—it’s a professional advantage.

Gain critical skills and IACET-approved CEUs that make a measurable difference.

Two labs, two answers

Scenario: a toxicology lab with 50 extracts a day

A forensic toxicology lab extracts 50 blood samples a day into a volatile organic solvent and needs them dried and reconstituted for LC-MS. A centrifugal concentrator works, but the batch waits for the slowest tube, and the lab runs its solvent at a temperature where gas flow is faster. A 48-position nitrogen evaporator in a fume hood handles each day’s batch in one run, with independent positions so a short batch doesn’t waste gas. Cylinder deliveries soon become a weekly chore, and the lab’s cost model points it toward an on-site generator.

Scenario: proteomics peptides in water and plates

A proteomics core dries peptide digests and fractions in aqueous solutions with small amounts of acid and acetonitrile, often in 96-well plates. Nitrogen blowdown struggles with the water and risks splashing between wells. A centrifugal vacuum concentrator dries whole plates at low temperature without bumping, with no gas to manage. The core keeps a small nitrogen evaporator for the occasional organic extract.

Practical tips for both

  • Match vessels to the instrument: tube diameters, plate formats, and rotor or block inserts must fit.
  • Protect against cross-contamination: avoid overfilled tubes, set needles above the sample, and use plate seals or mats as recommended.
  • Exhaust the vapors: blowdown units belong in a fume hood; centrifugal systems need cold traps and vented pumps.
  • Use clean solvent and gas: impurities concentrate along with your analytes; see our guide to choosing solvent grades.
  • Consider recovery: blowdown exhausts solvent; vacuum systems can capture it; see Solvent Recovery in the Lab: Cutting Purchase and Disposal Costs.
  • Keep the rotovap for what it does best: single, larger volumes; safety guidance is in our guide to rotary evaporator safety.

A nitrogen vs. centrifugal evaporator checklist

  1. List your solvents by boiling point. Volatile organics point to nitrogen blowdown; water, DMSO, and DMF point to centrifugal systems.
  2. Count samples and formats. Tubes and vials suit both; microplates usually favor centrifugal or plate-specific blowdown units.
  3. Decide whether samples can share conditions. Centrifugal systems treat every sample the same; blowdown positions can be adjusted individually.
  4. Model gas consumption honestly. Multiply flow per position by positions, minutes per day, and days per year; compare cylinder and generator costs.
  5. Account for the vacuum side. Centrifugal systems need pump maintenance, cold traps, and compatible components.
  6. Plan ventilation and safety. Blowdown solvent vapors need a fume hood; high nitrogen use needs ventilation and possibly oxygen monitoring.
  7. Test your own samples. Manufacturer speed comparisons are indicative; trial both methods with real samples before buying.
  8. Check recovery and contamination needs. Consider whether you need solvent back and how sensitive downstream analysis is to cross-contamination.

Neither technology is simply better. Nitrogen blowdown is the quick, flexible choice for volatile organics in tubes; centrifugal evaporation is the steady, gas-free choice for water, DMSO, and plates. Pick by solvent first, then do the gas math before you sign the purchase order.

 

This article was produced under Lab Manager’s AI Editorial Guidelines

Frequently Asked Questions (FAQs)

  • What is the difference between a nitrogen evaporator and a centrifugal evaporator?

    A nitrogen evaporator blows gas onto each heated sample at atmospheric pressure to sweep away vapor. A centrifugal evaporator spins samples under vacuum with heat, lowering boiling points and preventing bumping. Nitrogen blowdown suits volatile organics; centrifugal systems suit water, DMSO, and DMF.

  • Which is faster, nitrogen blowdown or centrifugal evaporation?

    It depends on the solvent. Nitrogen blowdown is often faster for volatile organic solvents such as methanol, while centrifugal evaporation is faster for water and high-boiling solvents such as DMSO and DMF.

  • How much nitrogen does a nitrogen evaporator use?

    It varies widely by model and settings, from about 0.33 L/min per position in one manufacturer’s analysis to 0.5 to 2 L/min per position in other estimates. A busy multi-position unit can use several cylinders a month or more.

  • Is a nitrogen generator worth it for an evaporator?

    For regular users it often is; one manufacturer’s analysis found on-site generation up to 65% cheaper than cylinders over 10 years, though savings depend on actual gas consumption.

  • Can centrifugal evaporators dry DMSO?

    Yes. Vacuum lowers DMSO’s boiling point, and high-performance centrifugal evaporators can remove DMSO while keeping samples below about 40 °C.

Add Lab Manager as a preferred source on Google

Add Lab Manager as a preferred Google source to see more of our trusted coverage.

About the Author

  • Trevor Henderson headshot

    Trevor Henderson BSc (HK), MSc, PhD (c), has more than two decades of experience in the fields of scientific and technical writing, editing, and creative content creation. With academic training in the areas of human biology, physical anthropology, and community health, he has a broad skill set of both laboratory and analytical skills. Since 2013, he has been working with LabX Media Group developing content solutions that engage and inform scientists and laboratorians. He can be reached at thenderson@labmanager.com.

    View Full Profile

Related Topics

Related Articles

Current Magazine Issue Background Image

CURRENT ISSUE - October 2026

Why Lab Teams Resist Change—And How Leaders Can Respond

Addressing the human side of automation, AI, and operational change

October 2026 Lab Manager Cover Image